Is a 2 stage furnace worth the extra cost?
Is a 2 stage furnace worth the extra cost?
Should I Buy a Two-Stage Furnace? You are most likely to benefit from owning a two-stage furnace if you own a two or multi-story home in which you intend to spend the next several years or more. Otherwise, you won’t get to reap the long-term benefits of lower energy bills.
Is a 2 stage furnace good?
The two-stage furnace is more efficient than the one-stage because it doesn’t release as much fuel into the heat exchanger when the home is only somewhat cold. If it’s 5 to 10 degrees outside, a two-stage furnace will run in the partially-open position and only use 70% of the energy it normally would.
How much does a new 2 stage furnace cost?
How Much Does a Two-Stage Furnace Cost? Mid-efficiency, two-stage furnaces costs about $2,500 to $4,000, including installation. The furnace itself usually costs $1,500 to $2,000, while labor adds an additional $1,000 to $2,000. High-efficiency models cost about $4,000 to $5,000 to buy and install.
What is better 1 stage or 2 stage furnace?
As is evident from the table, one-stage furnaces are the cheaper option in regard to installation costs. However, when looking at energy efficiency, two-stage furnaces tend to perform better. This means that two-stage furnaces may save you more money over time on your utility bill.
Are 2 stage furnaces quieter?
A two stage furnace is quieter and generates more even heat through the house. The longer, slower heating cycle eliminates the kind of rapid warming that many people find uncomfortable from a single stage furnace.
Does a 2 stage furnace use more electricity?
For two-stage designs, the DOE test procedure consistently shows a reduction in energy consumption by about 3% compared to single-stage furnaces at the same AFUE level. In contrast, the 2006 AHRAE test procedure shows almost no difference in the total energy consumption at the same efficiency level.
How much does a 40000 BTU furnace cost?
Gas Furnace Price Factors
| Furnace Size (BTU) | Typical Furnace Cost with Installation* |
|---|---|
| 40,000 | $2,000 – $3,500 |
| 50,000 | $2,300 – $3,800 |
| 60,000 | $2,500 – $4,200 |
| 75,000 | $2,700 – $4,600 |
What size furnace do I need for a 2000 square-foot home?
Rough Estimates A mid-sized home of 2,000 square feet would need approximately 50,000 to 60,000 Btu to heat it properly. With a less efficient furnace operating at 80 percent efficiency this would require a 60,000- to 72,000-Btu furnace.
How much quieter is a two-stage furnace?
b. 65% for two-stage. This means the circulating and combustion blowers can operate at even lower speeds, with a corresponding reduction in combustion intensity.
Does a 2 stage furnace need a special thermostat?
Using a 2 stage thermostat will not harm the furnace. And because the control board is compatible with a single stage thermostat, the furnace will still operate both stages. The control board would, as you say, start the second stage after about 10 minutes.
What are the advantages of a 2 stage furnace?
Two-stage furnaces are able to produce more even heat distribution by using two levels of heat output. This allows the furnace to use technology to determine what level of heat output is needed for the current situation. These settings would include high for extreme cold and low for milder days.
How many square feet will a 45000 BTU furnace heat?
1,000 square feet
Heating BTUs Table (Rough Estimates)
| Home Size (Heating): | Standard Climate | Very Hot Climate |
|---|---|---|
| 500 square feet | 22,500 BTU | 15,000 BTU |
| 1,000 square feet | 45,000 BTU | 30,000 BTU |
| 1,500 square feet | 67,500 BTU | 45,000 BTU |
| 2,000 square feet | 90,000 BTU | 60,000 BTU |